Short answer: An electric cooktop that will not heat usually has one of seven problems: a tripped double breaker, the cooktop lock turned on, a burned-out burner element, a failed infinite switch behind the knob, a loose or burned terminal block, a bad limiter on a glass-top element, or a control board fault on touch models. If one burner is out, think element or switch. If all are out, think power. Call (830) 240-5230 for help.
A dead burner always shows up at the worst time, like when the pot for Sunday dinner will not boil. Electric cooktops are simple at heart: power comes in at 240 volts, a switch or control decides how much reaches each element, and the element turns that power into heat. When something in that chain fails, the burner stays cold or only gets warm. Here is how to find which link broke.

Is it one burner or all of them?
Start by turning each burner on high for a minute. If only one stays cold, the problem is in that burner’s own parts: the element, its switch or its wiring. If every burner is cold, look at power first: the breaker, the cooktop lock, the main power connection or the control board. If burners heat but only get warm, a switch or a glass-top limiter is often the cause.
| What you see | Most likely cause | DIY or pro? |
|---|---|---|
| One burner completely cold | Element, infinite switch or terminal | Coil swap DIY; others pro |
| All burners cold, clock works | Half of the double breaker tripped | DIY: reset both halves |
| All burners cold, display shows a lock | Cooktop lock is on | DIY: hold the lock key |
| Burner only gets warm, never red | Infinite switch or glass-top limiter | Pro |
| Burner stuck on high | Infinite switch welded closed | Pro, turn off at breaker |
| Burner works only when wiggled | Loose coil or burned terminal block | Pro |
| Touch controls dead or beeping | Control board or touch panel | Pro |
What can you check safely before calling?
You can check power, settings and coil burners without opening the cooktop. Reset the breaker by switching both halves fully off and back on. Look for a lock symbol on touch models. On coil tops, turn the power off, then swap a dead coil with a working one of the same size. If the dead coil heats in the other spot, the coil is fine and the switch or terminal is bad.
- Turn every burner to off before you start.
- Reset the cooktop breaker, the double-wide switch in the panel.
- On touch models, hold the lock key for a few seconds to unlock.
- On coil tops, with power off, swap the dead coil with a working one of the same size.
- Look at the coil ends and the socket for black, pitted or melted spots.
- Never test a burner by touching it, and never run a glass top that is cracked.
Why does a burner only get warm and not hot?
The knob on most electric cooktops controls an infinite switch that cycles power on and off to set the heat level. When the contacts inside wear out, the switch may only send short bursts of power, so the burner stays warm. On glass tops, each radiant element has a limiter that cuts power to protect the glass, and a weak limiter can shut the element off too early.
Both parts are specific to your model. A technician tests the switch and element with a meter so you replace only the part that failed, not every part that might be guilty.
What about glass-top cooktops?
Glass-top cooktops hide a coil-like radiant element under the glass. You cannot swap these by hand the way you can a plug-in coil. If one zone will not glow, the element, its limiter or its switch is usually the cause. A cracked glass top is a separate problem and is unsafe to use, because spills can reach live parts.
If you see a crack or chip, stop using the cooktop and read what to do about a cracked glass cooktop before you decide on repair or replacement. Never set hot pans or heavy cast iron down hard on the glass, and clean spills before they bake on.
When should you call a technician?
Call when a burner is stuck on high, when you see sparks, smell burning plastic or see melted wiring, when coils work only when moved, when every burner is dead and the breaker is fine, or when a glass-top zone or touch panel fails. These jobs mean working with 240-volt wiring inside the appliance.
Our technicians handle cooktop repair in New Braunfels for GE, Whirlpool, Frigidaire, Samsung, LG, KitchenAid and other brands, on both freestanding ranges and built-in cooktops.
How much does electric cooktop repair cost?
Our diagnostic visit is approx. $90 to $100, and it is applied to the repair if you go ahead. Labor runs approx. $50 to $95 per hour, plus the part for your model. Coil elements and terminal blocks are usually on the lower end, while glass-top radiant elements, touch control boards and glass tops cost more. You get the full price before any work starts.
If the cooktop is older and needs a new glass top or a control board, it is worth comparing the repair price with a new unit. For a dead element or switch on a newer cooktop, repair is almost always the better deal.
How can you keep your cooktop working?
Use flat-bottomed pans that match the burner size, keep coil drip pans clean so grease cannot burn the terminals, wipe glass tops with a cooktop cleaner instead of abrasive pads, and do not let pots boil dry. If a burner starts acting up, stop using it before a small switch problem burns the wiring.
We serve New Braunfels, Gruene, Canyon Lake, Garden Ridge, Bulverde and nearby Comal and Guadalupe County homes. As the appliance guys New Braunfels homeowners call for every room, we also repair ovens, refrigerators, washers, dryers, dishwashers and garbage disposals.
Frequently Asked Questions
Why is one burner on my electric cooktop not heating?
When only one burner is dead, the cause is usually that burner’s element, its infinite switch (the control knob switch), or on coil tops a loose or burned terminal block. On glass tops, the radiant element under the glass or its limiter can fail. The other burners working rules out the breaker and main power.
Why are none of the burners on my electric cooktop working?
If every burner is cold, check the circuit breaker first. Electric cooktops use a 240-volt double breaker, and one half can trip while the clock or lights still work. A lockout setting, a failed control board on touch-control models or a burned power connection can also stop all burners.
Can I replace a cooktop burner myself?
On coil-top ranges, plug-in coil elements can often be swapped by the homeowner with the power off. Glass-top radiant elements, infinite switches, control boards and wiring connections mean working inside a 240-volt appliance, so a technician should handle those.
Is it worth repairing an electric cooktop?
Usually yes. Burner elements, switches and terminal blocks are common, moderately priced repairs. If the glass top is cracked or a touch-control board fails on an older cooktop, compare the repair price with a new cooktop before deciding.
How much does cooktop repair cost in New Braunfels?
Our diagnostic visit is approx. $90 to $100 and is applied to the repair if you go ahead. Labor runs approx. $50 to $95 per hour plus the part for your model, and you get the full price before any work starts.
Get your appliance working again
Call New Braunfels Appliance Fix at (830) 240-5230 or send us a message on our contact page. We will confirm the price before any work starts.
Talk to a local appliance technician today.
Call Now – (830) 240-5230