You start a load, hear a hum or a click, and nothing happens. Or water trickles in so slowly the cycle never moves on. A washer not filling with water is a common problem, and many causes are simple to check. The trick is to start at the water supply and work toward the washer’s parts.
Need a technician? Our washer repair New Braunfels team fixes fill, drain and spin problems on all major brands.
This guide walks you through the common causes, what you can check yourself and when to call. For help in New Braunfels, call New Braunfels Appliance Fix at (830) 240-5230.
Why is my washer not filling with water?
The most common causes are faucets that are closed or only partly open, kinked or crushed fill hoses, clogged inlet screens, a failed water inlet valve, a bad lid or door switch, and a faulty water level sensor or control. Low house water pressure can also make a washer fill so slowly that it times out with an error.
Safety first
Unplug the washer before you pull it out or remove hoses. Turn off both faucets first and keep a towel and bucket handy, since hoses hold water. If water is spraying from a hose or faucet, shut the faucets right away.
Common causes and fixes
1. Faucets closed or partly closed
The hot and cold faucets behind the washer can get bumped or were never opened all the way after a move. Turn both fully counterclockwise. Old faucets can also fail inside and stay partly closed even when the handle turns.
2. Kinked or crushed hoses
Pushing the washer back against the wall can bend a fill hose and cut off the water. Pull the washer out a few inches and straighten the hoses. Replace any hose that is cracked, bulging or more than about 5 years old.
3. Clogged inlet screens
Small mesh screens sit where the hoses connect to the washer, and sometimes in the hose ends. They catch sand, rust and minerals. Hard water in the New Braunfels area leaves scale that can clog them over time. Rinse them gently under the tap.
4. Failed water inlet valve
The inlet valve opens to let water in when the control tells it to. If its coil burns out or it gets clogged inside, the washer hums but no water flows, or only hot or only cold comes in. This part is replaced, not repaired.
5. Lid or door switch
Many washers will not fill until the lid or door switch says it is closed. If the switch or latch fails, the washer may light up but never start filling. If the door also stays locked, our guide on a washer that won’t start covers related causes.
6. Water level sensor or control board
A pressure switch or sensor tells the washer how full the tub is. If it reads wrong, the washer may think it is already full and skip the fill. A control board fault can also stop the fill. These need testing with a meter.
Washer still won’t fill? A local technician can test the valve and switches today.
Call Now – (830) 240-5230Quick guide: what the symptom tells you
| What you notice | Likely cause | DIY or pro? |
|---|---|---|
| No water at all, washer hums | Closed faucet or failed inlet valve | Check faucets; valve is pro |
| Water trickles in slowly | Clogged screens or low pressure | DIY cleaning |
| Only hot or only cold fills | One side of the valve or hose blocked | Check hose; valve is pro |
| Lights on, no fill, no sound | Lid or door switch, control | Pro |
| Fills a little then stops | Water level sensor or pressure hose | Pro |
What you can check before calling
- Open both faucets fully and check that other taps in the house have good pressure.
- Pull the washer out and straighten the hoses.
- Turn off the faucets, unplug the washer and clean the inlet screens.
- Close the lid or door firmly and listen for the latch click.
- Unplug the washer for one minute to reset the control, then try a rinse cycle.
If the washer fills but has other problems, such as a smell, see our guide to a washing machine that smells bad.
How much does washer repair cost in New Braunfels?
Our diagnostic visit is approx. $90–$100, and it is applied to the repair if you go ahead. Labor runs approx. $50–$95 per hour, plus parts if needed. We confirm the total with you before any work starts. Many fill problems are fixed with cleaning or a new hose. If the inlet valve, switch or sensor has failed, we will show you the cost before any work starts.
Prices are approximate and depend on your washer’s brand, model, and the part needed.
Washer repair in New Braunfels
We repair Whirlpool, Maytag, GE, Samsung, LG, Speed Queen and most other washer brands. We serve homes in Downtown New Braunfels, the Gruene Historic District, Landa Park, Vintage Oaks, Veramendi, and across Comal and Guadalupe Counties. If you are looking for the appliance guys New Braunfels homeowners call for laundry problems, we are a phone call away. Learn more about our washer repair in New Braunfels.
Not sure if other appliances need attention? Read 7 Signs Your Appliance Needs Repair (Before It Breaks Down).
Frequently Asked Questions
Why is my washer not filling with water?
The most common causes are closed or partly closed faucets, kinked hoses, clogged inlet screens, a failed water inlet valve, a bad lid or door switch, or a faulty water level sensor.
Why does my washer fill so slowly?
Slow filling usually means low water pressure or clogged screens in the hose ends or inlet valve. Hard water minerals can build up in those screens.
Can I clean the washer inlet screens myself?
Yes. Turn off both faucets, unplug the washer, remove the hoses and gently rinse the small screens. Do not remove them if they are part of the valve.
Why does my washer fill with only hot or only cold water?
One side of the inlet valve may have failed, or one hose or faucet may be blocked. Check that both faucets are fully open first.
How much does washer repair cost in New Braunfels?
Our diagnostic visit is approx. $90–$100, applied to the repair if you go ahead. Labor runs approx. $50–$95 per hour plus parts. You get the price before work starts.
Get your appliance working again
Call New Braunfels Appliance Fix at (830) 240-5230 or send us a message on our contact page. We will confirm the price before any work starts.
Talk to a local appliance technician today.
Call Now – (830) 240-5230